Pololu 2286 - 75:1 Metal Gearmotor 25Dx54L mm with 48 CPR Encoder
search
  • Pololu 2286 - 75:1 Metal Gearmotor 25Dx54L mm with 48 CPR Encoder
ID: 195958
155,79 zł
Brutto

126,66 zł Netto

75:1 Metal Gearmotor 25Dx54L mm with 48 CPR Encoder

24h
Dostępny
Dostępna ilość: 1
 

Wysyłka gratis

darmowa wysyłka na terenie Polski dla wszystkich zamówień powyżej 500 PLN

 

Wysyłka tego samego dnia

Jeśli Twoja wpłata zostanie zaksięgowana na naszym koncie do godz. 11:00

 

14 dni na zwrot

Każdy konsument może zwrócić zakupiony towar w ciągu 14 dni bez zbędnych pytań

75:1 Metal Gearmotor 25Dx54L mm with 48 CPR Encoder

This cylindrical, 2.62" x 0.98" x 0.98" brushed DC gearmotor with a 74.83:1 metal gearbox is a lower-current alternative to the HP version. It has an integrated 48 CPR quadrature encoder on the motor shaft, which provides 3592 counts per revolution of the gearbox’s output shaft. These units have a 0.315"-long, 4 mm-diameter D-shaped output shaft. This gearmotor is also available without an encoder.

Key specs at 6 V: 75 RPM and 80 mA free-run, 85 oz-in (6.1 kg-cm) and 2.2 A stall.

Gearmotor Options

This brushed DC gearmotor is available in high- and low-power versions in a number of gear ratios. Many other gear ratios are also available without an encoder.

Gear RatioSpeed
@ 6V
Stall Torque
@ 6V
Stall Current
@ 6V


With Encoder


Without Encoder
4.4:1 2020 RPM 8 oz-in 6 A 25Dx48L mm HP
1280 RPM 5 oz-in 2.2 A 25Dx48L mm
9.7:1 1010 RPM 17 oz-in 6 A 25Dx48L mm HP 25Dx48L mm HP
580 RPM 11 oz-in 2.2 A 25Dx48L mm 25Dx48L mm
20.4:1 480 RPM 36 oz-in 6 A 25Dx50L mm HP
275 RPM 24 oz-in 2.2 A 25Dx50L mm
34:1 285 RPM 60 oz-in 6 A 25Dx52L mm HP 25Dx52L mm HP
165 RPM 40 oz-in 2.2 A 25Dx52L mm 25Dx52L mm
47:1 210 RPM 80 oz-in 6 A 25Dx52L mm HP 25Dx52L mm HP
120 RPM 50 oz-in 2.2 A 25Dx52L mm 25Dx52L mm
75:1 130 RPM 130 oz-in 6 A 25Dx54L mm HP 25Dx54L mm HP
75 RPM 85 oz-in 2.2 A 25Dx54L mm 25Dx54L mm
99:1 100 RPM 160 oz-in 6 A 25Dx54L mm HP
57 RPM 110 oz-in 2.2 A 25Dx54L mm
172:1 57 RPM 260 oz-in 6 A 25Dx56L mm HP
33 RPM 170 oz-in 2.2 A 25Dx56L mm 25Dx56L mm
227:1 25 RPM 220 oz-in 2.2 A 25Dx56L mm
378:1 15 RPM 250 oz-in 2.2 A 25Dx58L mm
499:1 12 RPM 300 oz-in 2.2 A 25Dx58L mm

Note: At some of the higher gear ratios, these motors can generate enough torque to damage themselves. Any torque greater than about 250 oz-in (18 kg-cm) is likely to damage the gearbox, so we recommend that you avoid stalling the 172:1 HP, 227:1, 378:1, and 499:1 versions of these motors at 6 V.

These motors are intended for use at 6 V. In general, these kinds of motors can run at voltages above and below this nominal voltage, so they should comfortably operate in the 3 – 9 V range, though they can begin rotating at voltages as low as 1 V. Higher voltages could start negatively affecting the life of the motor.

Gearmotor Dimensions

These gearmotors have output shafts with a diameter of 4 mm. The Pololu universal aluminum mounting hub for 4mm shafts can be used to mount our larger Pololu wheels (60mm-, 70mm-, 80mm-, and 90mm-diameter) or custom wheels and mechanisms to the gearmotor’s output shaft (see the left picture below). These are the same type of motors used in the Wild Thumper all-terrain chassis, and the gearbox’s output shaft works directly with the 120mm-diameter Wild Thumper wheels.

25D mm metal gear motor with 48 CPR encoder and Pololu 60×8mm wheel.

The face plate has two mounting holes threaded for M3 screws. You can use our custom-designed 25D mm metal gearmotor bracket (shown in the picture below) to mount the gearmotor to your project via these mounting holes and the screws that come with the bracket.

Pololu 25D mm gearmotor with bracket.

The diagram below shows the dimensions (in mm) of the 25D mm line of gearmotors. The value of L is shown in the table below.

Dimension diagram (in mm) for the 25D mm metal gearmotors.

Gear RatioL (mm)
4.4:1
9.7:1
17
20.4:1 19
34.1
47:1
21
75:1
99:1
23
172:1
227:1
25
378:1
499:1
27

25D mm metal gearmotor with 48 CPR encoder.

Using the Encoder

A two-channel Hall effect encoder is used to sense the rotation of a magnetic disk on a rear protrusion of the motor shaft. The quadrature encoder provides a resolution of 48 counts per revolution of the motor shaft. To compute the counts per revolution of the gearbox output, multiply the gear ratio by 48. The motor/encoder has six color-coded, 11" (28 cm) leads:

ColorFunction
Black motor power
Red motor power
Blue Hall sensor Vcc (3.5 – 20 V)
Green Hall sensor GND
Yellow Hall sensor A output
White Hall sensor B output

These leads have stripped, unterminated ends that can be soldered or crimped to make solder free connectors. The Hall sensor requires an input voltage, Vcc, between 3.5 and 20 V and draws a maximum of 10 mA. The A and B outputs are square waves from 0 V to Vcc approximately 90° out of phase. The frequency of the transitions tells you the speed of the motor, and the order of the transitions tells you the direction. The following oscilloscope capture shows the A and B (yellow and white) encoder outputs using a motor voltage of 6 V and a Hall sensor Vcc of 5 V:

Encoder A and B outputs for 25D mm HP metal gearmotor with 48 CPR encoder (motor running at 6 V).

By counting both the rising and falling edges of both the A and B outputs, it is possible to get 48 counts per revolution of the motor shaft. Using just a single edge of one channel results in 12 counts per revolution of the motor shaft, so the frequency of the A output in the above oscilloscope capture is 12 times the motor rotation frequency.

May 5, 2012 Update: We are transitioning to encoders with leads terminated by a 1×6 0.1” female header. If you receive an encoder with such a header, you can pull the crimped wires out of the header or cut the header off if you just want the individual wires.

Selecting the Right Gearmotor

We offer a wide selection of metal gearmotors that offer different combinations of speed and torque. Our metal gearmotor comparison table can help you find the motor that best meets your project’s requirements.

Some of the Pololu metal gearmotors.

People often buy this product together with:

MC33926 Motor Driver Carrier MC33926 Motor Driver Carrier
Pololu Universal Aluminum Mounting Hub for 4mm Shaft Pair, 4-40 Holes Pololu Universal Aluminum Mounting Hub for 4mm Shaft Pair, 4-40 Holes
Pololu 25D mm Metal Gearmotor Bracket Pair Pololu 25D mm Metal Gearmotor Bracket Pair
195958

Cechy

Moc silnika DC
LP
Materiał przekładni
Metalowa
Przełożenie
75:1
Prędkość obrotowa
75 RPM
Średnica wału
4 mm
Kształt wału
Litera D
Obustronny wał silnika
Tak
Napięcie zasilania
6 V

Produkty z tej samej kategorii (16)

W ramach naszej witryny stosujemy pliki cookies w celu świadczenia Państwu usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Więcej szczegółów w naszej polityce prywatności.